返回主站 | 设为首页 | 加入收藏      
   
 
  首页 关于我们 产品展示 方案设计 技术分享 行业资讯 联系我们  
 
马达驱动IC/步进电机控制芯片
直流电机驱动芯片
步进电机驱动芯片(并行接口)
步进电机驱动芯片(步进/方向接口&串行接口)
功放IC
音量控制IC
TFT-Driver IC
TFT-LCD 时序控制IC
触摸屏控制IC
LED照明驱动IC
锁相环IC
USB声卡IC
功率半导体器件
STN Driver IC
视频IC
HDMI IC
FM解调IC
模拟开关阵列IC
LCD显示驱动IC
马达驱动IC/步进电机控制芯片
电源管理IC
电容式触摸感应IC
LED音乐频谱IC
音频CODEC IC
Lightning闪电数据接口IC
 
名称:
种类:
类别:

电 话:0755-82863877
传 真:0755-82863778
手 机:13242913995

E-MAIL:panxia168@126.com

联系人:潘先生
地 址:深圳市宝安西乡航城大道航城创新创业园A4栋218

 
当前位置:首页 -> 方案设计
MTS2916A双极步进马达驱动方案
文章来源: 更新时间:2015/9/23 15:16:00
Microchip公司的MTS2916A是双极马达驱动器,也能双向控制两个DC马达,两个单独的H桥输出提供电压40V,连续电流750mA,主要用在步进马达,DC马达,汽车HVAC和座位控制.本文介绍了MTS2916A主要特性,框图和应用电路,以及评估板ADM00308主要特性,电路图,材料清单和PCB设计文件.
The MTS2916A motor driver is a CMOS devicecapable of driving both windings of a bipolar steppermotor or bidirectionally control two DC motors. Each ofthe two independent H-bridge outputs is capable ofsustaining 40V and delivering up to 750 mA of
continuous current. The output current level iscontrolled by an internal pulse-width modulation(PWM) circuit that is configured using two logic inputs,a current sense resistor and a selectable referencevoltage. The H-bridge outputs have been optimized toprovide a low output saturation voltage drop.
Full, half, and micro-stepping operations are possiblewith the PWM current control and logic inputs. Themaximum output current is set by a sensing resistorand a user selectable reference voltage. The outputcurrent limit is selected using two logic level inputs. Theselectable output current limits are 0%, 33%, 67%, or100% of the maximum output current. Each bridge hasa PHASE input signal which is used to control the directionof current flow through the H-bridge and the load.
The H-bridge power stage is controlled by non-overlappingsignals which prevent current cross conductionwhen switching the direction of the current flow. Internalclamp diodes protect against inductive transients.
Thermal protection circuitry disables the outputs whenthe junction temperature exceeds the safe operatinglimit. No special power-up sequencing is required.
Undervoltage Lockout circuitry prevents the chip fromoperating when the load supply is applied prior to thelogic supply.
The device is supplied in a 24-pin SOP package.

MTS2916A主要特性:
• 750 mA Continuous Output Current
• Load Voltage Supply: 10V to 40V
• Full Bipolar Stepper Motor Drive Capability
• Bidirectional DC Motor Capability
• Internal Fixed TOFF Time PWM Current Control
• Internal Protection Diodes
• Internal Thermal Shutdown
• Under Voltage Lockout
• LS-TTL Compatible Logic Inputs with Pull-UpResistors
• Low RON Output Resistance
• Low Quiescent Current
• Operating Temperature Range: -40℃ to +105℃
• Pin Compatible with Allegro 2916

MTS2916A应用:
• Stepper Motor Actuators
• DC Motor Actuators
• Automotive HVAC Ventilation
• Automotive Power Seats

图1. MTS2916A框图

图2. MTS2916A典型应用框图

MTS2916A双全桥步进马达评估板ADM00308
The MTS2916A Dual Full-Bridge Stepper Motor Driver Evaluation Board demonstrates the capabilities of the MTS2916A to control both windings of a bipolar stepper motor. The board also demonstrates the capabilities of the MTS62C19A, which has the same functionality, but different pin assignments. A PIC16F883 is utilized for motor control processing.
This evaluation board incorporates features through the implementation of push button switches and a variable speed input potentiometer to exercise a stepper motor in Full-Step, Half-Step, Modified Half-Step and Microstepping modes. LEDs indicate a binary representation of which mode has been selected. The evaluation board and the stepper motor can be powered from a single power input J1 (7 VDC to 12 VDC) with jumper JP2 installed. For higher motor voltages, make sure JP2 is not installed, and connect VLOAD at J4. Numerous test points have been designed into the board to allow easy access.

MTS2916A评估板ADM00308主要特性:
Push Button mode, Run, Hold and Direction control
Potentiometer variable speed adjustment
LED mode indication
Maximum winding current with the combination of Rs, VREF and conditioning of I0/I1 logic inputs
PICkit™ Programming connector (J5) to implement user-created code

图3.评估板ADM00308外形图

图4.评估板ADM00308电路图
评估板ADM00308材料清单:



图5.评估板ADM00308 PCB设计图(1)

图6.评估板ADM00308 PCB设计图(2)

图7.评估板ADM00308 PCB设计图(3)


 
 
 
    相关产品  
 
深圳市永阜康科技有限公司  服务热线:0755-82863877 手机:13242913995