 |
|
| |
|
|
业务洽谈：
联系人：张顺平
手机：17727550196（微信同号）
QQ:3003262363
EMAIL:zsp2018@szczkjgs.com
联系人：鄢先辉
手机：17727552449 （微信同号）
QQ:2850985542
EMAIL:yanxianhui@szczkjgs.com
负责人联络方式：
手机：13713728695（微信同号）
QQ:3003207580
EMAIL:panbo@szczkjgs.com
联系人：潘波 |
|
|
| |
|
 |
|
 |
当前位置：首页 -> 方案设计 |
|
|
| DRV8846 3D打印机马达控制器参考设计 |
|
|
| 文章来源： 更新时间：2014/12/15 9:38:00 |
|
TI公司的DRV8846是高度集成的步进马达驱动器,包括两个H桥和微步进分度器,工作电压4-18V,驱动电流高达1A,主要用在打印机,扫描仪,视频安全摄像机和投映仪.本文介绍了DRV8846主要特性,功能框图,应用电路以及评估板主要特性,电路图和材料清单,以及3D打印机控制器(12V)主要特性,电路图和材料清单.
The DRV8846 provides a highly-integrated stepper motor driver for cameras, printers, projectors, and other automated equipment applications. The device has two H-bridges and a microstepping indexer and is intended to drive a bipolar stepper motor. The output block of each H-bridge driver consists of N- channel and P-channel power MOSFETs configured as full H-bridges to drive the motor windings. The DRV8846 is capable of driving up to 1-A full scale
output current (with proper heatsinking and TA = 25℃).
A simple STEP/DIR interface allows easy interfacing to controller circuits. Pins allow configuration of the motor in full-step up to 1/32-step modes. Decay mode is configurable so that adaptive decay, slow decay, fast decay, and mixed decay can be used. The PWM
current chopping off-time can also be selected. A low-power sleep mode is provided which shuts down internal circuitry to achieve very-low quiescent current draw. This sleep mode can be set using a dedicated nSLEEP pin.
Internal protection functions are provided for UVLO,overcurrent protection, short circuit protection, and overtemperature. Fault conditions are indicated via a nFAULT pin.
DRV8846主要特性:
1• PWM Microstepping Motor Driver
– Built-In Microstepping Indexer
– Up to 1/32 Microstepping
– Step/Direction Control
• Multiple Decay Modes
– Adaptive Decay
– Mixed Decay
– Slow Decay
– Fast Decay
• Configurable Off-Time PWM Chopping
– 10-, 20-, or 30-μs Off-Time
• Adaptive Blanking Time for Smooth Stepping
• 4- to 18-V Operating Supply Voltage Range
• 1-A Continuous/RMS Output Current (at 25℃)
• Low-Current Sleep Mode
• 3-Bit Torque DAC to Scale Motor Current
• Thermally Enhanced Surface Mount Package
• Protection Features
– VM Undervoltage Lockout (UVLO)
– Overcurrent Protection (OCP)
– Thermal Shutdown (TSD)
– Fault Condition Indication Pin (nFAULT)
DRV8846主要应用:
• Printers
• Scanners
• Video Security Cameras
• Projectors
图1. DRV8846功能框图
图2. DRV8846 PWM马达驱动器电路图
图3. DRV8846 典型应用电路图
评估板
The DRV8846 customer EVM is a platform revolving around the DRV8846, a low voltage dual H-bridge driver and highly configurable power stage. This device has been optimized to drive a single bipolar stepper with up to 32 degrees of internally generated microstepping.
The EVM houses an MSP430 microcontroller and a USB interface chip. The USB chip allows for serial communications from a PC computer where a Microsoft® Windows® application is used to schedule serial commands. These commands can be used to control each of the device’s signals, and drive the stepper motor by issuing the step commands at the desired rate.
The microcontroller firmware operates using internal index mode.
This user’s guide details the operation of the EVM, as well as the hardware configurability of the evaluation module.
图4.评估板PCB外形图
图5.评估板连接图
图6.评估板电路图(1)
图7.评估板电路图(2)
评估板材料清单:
3D打印机控制器(12V)
This design is a complete system for controlling 3-axis, single extruder-based 3D printers. The system is managed by the MSP430F5529 LaunchPad and utilizes the DRV8846 for precision stepper motor control. The CSD18534Q5A is used as a low-side switch for the hot bed heater, extruder heater, and cooling fan. The DRV5033 Hall Sensor acts as a contactless limit switch.
3D打印机控制器(12V)主要特性:
Complete 3D printer controller with MCU, stepper drivers, heater outputs, sensor inputs, and SD card slot.
Precise stepper motor current regulation using DRV8846 adaptive decay
Hall sensor limit switches are immune to contaminants and never wear out
High-current heater outputs from the CSD18534Q5A with low 7.8 mΩ Rds(ON)
Powered from a single 12V supply
System has been fully tested and proven
图8.3D打印机TIDA-00405外形图
图9.3D打印机TIDA-00405电路图(1)
图10.3D打印机TIDA-00405电路图(2)
图11.3D打印机TIDA-00405电路图(3)
图12.3D打印机TIDA-00405电路图(4)
图13.3D打印机TIDA-00405电路图(5)
3D打印机TIDA-00405系统材料清单:
|
|
| |
| |
|
|
|
